TY-HT400 Well service pump

TianyunMfg HT-400 pump comes in handy particularly when accurate pumping levels and controllability is the ultimate need. The entire components and parts which a TY HT-400 pump possess are replaceable. There is a wide variety of fluid ends with which a pump could be attached in tandem, depending on the specifications needed for a specific operation.

The following sizes are manufactured for the TY-HT400 pump by TianyunMfg. The sizes are used for specific purposes like simulation and drilling, for simulation purposes the sizes include 6 inches, 5 inches, 4.5 inches, 4 inches, and 3.37 inches. For drilling service, the size ranges from 6 inches to 3.5 inches.

You can also read the below table:

The applications of TY-HT400 pump include:

• Well pumping
• Cementing of Wells
• Fracturing and
• Acidizing

Using a TianyunMfg TY-HT400 well service pump, you will have benefits that include:

• Fuel efficiency by employing an efficient diesel-driven technology.
• High fuel carrying capacity of up to 130 gallons.
• Able to pump at extreme pressures of up to 20,000 psi or more.
• Consignment is relatively easy and can be shifted pretty easily and quickly due to the high portability.
• The durable and long-lasting module which will last for a longer stretch of time.
• Triple fluid end attachments.

The peak pressure for the operability of the TY-HT400 pump varies depending on what kind of operation is being performed, for cementing operations the peak pressure is about 9,000 psi to 20,000 psi, and for industrial level drilling services the pressure ranges from 4500 psi to 10,000 psi.

You can also read the below table to understand the Maximum Pressure:

Here list some frequently needed power end components for HT400 pump refurbishment and repair works:

• Gear assembly
• Ring gear assembly
• Crosshead and connecting rod sub-assembly
• Crosshead slide sub-assembly
• Main bearings for outboard and inboard
• Crankshaft
• Connecting Rods

Contact TianyuMfg to support your HT400 power end repair work.

After manufacturing the TianyunMfg TY-HT400 pump undergoes a strenuous testing procedure to ensure the best possible efficacy. These tests are necessary before moving the pump to the pumping site to avoid any mishap. The Chambers for fluid end are tested under extreme pressures which are far beyond the usual pressure threshold on the ground. After the assembly of fluid end Chambers, they are tested once again under extreme pressure conditions. The pump is tested for the third time when it is attached to the power end paraphernalia. Power end modules also undergo strenuous testing in the TianyuMfg testing facility.

After an hour of rigorous testing under increasing pressure and speed, the pump is assembled with the rest of the unit. After the culmination of testing at the testing site, the pump is further tested during the final inspection.

TianyunMfg TY-HT400 triplex pump has some frequently needed replaceable components. These parts can be replaced or added according to the specifications of the required operation. The most frequently needed replaceable parts of TY-HT400 triplex pump are as follows:

• Discharge Valve Subassembly
  • Valve, Frac
  • Insert, Valve
  • Spring, lock, suction stop
  • Retainer, stop and spring
  • Liner, 2pc bushing, valve guide
  • Seat Valve, Tapered
  • O ring
• Packing Nut and Packing Subassembly
  • Sleeve, wiper gland
  • Carrier, Seal&Packing
  • O-ring, 90D
  • Ring, backup, packing
  • Packing set
  • Ring, header
  • Adapter, header ring
  • Seal, lube, packing
• Push Rod Subassembly
• Fluid End Module
  • Fluid end section
  • Stud, fluid end to power end
  • Washer, lock, suction manifold
  • Flange, discharge, blank
• Suction Valve Subassembly
• Plunger/Cylinder Head Cover Subassembly
  • Retainer, cover
  • Gasket, cover
  • Nose, plunger
  • Seal, plunger nose assembly
  • Plunger, hard surface
  • Tie rod, plunger

Contact TianyuMfg if you ever need any consumables on HT400 pump parts list.

TianyuMfg supplies specific valve seat puller for HT400 valve seats replacement jobs. TianyuMfg HT400 valve seat puller consists of various components including clapper, lead screw, hydraulic actuator, and hand pump, and nut.

TianyuMfg valve seat puller is very easy to use and its maintenance is also relatively simple and easy. All you have to do is to insert the clapper inside the valve seat and screw the lead screws, then insert the actuator through the lead screw and place it on the cylinder, Screw the nuts and turn on the hand pump, this way you can remove the valve seats with ease.